STUDY OF THEORETICAL AND EXPERIMENTAL ASPECTS OF FLUID MOTION THROUGH PLASTICALLY DEFORMABLE POROUS MEDIA AS AN APPLICATION TO OILSEED EXTRACTION PROCESS BY THE SCREW PRESS

Authors

  • E.V. Slavnov Institute of Continuous Media Mechanics UB RAS
  • O.I. Skul’skiy Institute of Continuous Media Mechanics UB RAS
  • I.A. Petrov Perm National Research Polytechnic University
  • S.D. Anferov Perm National Research Polytechnic University
  • A.I. Sudakov Institute of Continuous Media Mechanics UB RAS
  • N.V. Shakirov Institute of Continuous Media Mechanics UB RAS

DOI:

Keywords:

deformable porous medium, oilseed extraction, permeability, mathematical modeling

Abstract

The paper presents the results of an experimental and theoretical investigation of fluid motion through plastically deformable porous media during oilseed extraction process by the screw press. It is shown that filtering properties change significantly due to bulk concentration and pressure. The influence of loading rate on the process of oil extraction is analyzed. The minimum residual oil content is evaluated. Some aspects concerning mathematical modeling of the examined process are discussed.

Supporting Agencies
Работа выполнена при финансовой поддержке РФФИ (грант № 13-08-96006).

Author Biographies

  • E.V. Slavnov, Institute of Continuous Media Mechanics UB RAS
    доктор технических наук, заведующий лабораторией механики термопластов
  • O.I. Skul’skiy, Institute of Continuous Media Mechanics UB RAS
    доктор технических наук, ведущий научный сотрудник лаборатории механики термопластов
  • I.A. Petrov, Perm National Research Polytechnic University
    доцент кафедры прикладной математики
  • S.D. Anferov, Perm National Research Polytechnic University
    старший преподаватель кафедры прикладной математики
  • A.I. Sudakov, Institute of Continuous Media Mechanics UB RAS
    ведущий инженер лаборатории механики термопластов
  • N.V. Shakirov, Institute of Continuous Media Mechanics UB RAS
    ведущий инженер лаборатории механики термопластов

References

  1. Anferov S.D., Skul’skij O.I. Modelirovanie fil’tracii zidkosti cerez plasticeski deformiruemuu poristuu sredu v processe ekstruzionnogo otzima // Vest. Perm. nac. issled. politehn. un-ta. Mehanika. - 2014. - No 2. - S. 29-47.
  2. Anferov S.D., Skul’skij O.I., Slavnov E.V. Matematiceskaa model’ deformirovania nasysennoj poristoj sredy pri mehaniceskom otzime // HI Vseros. s"ezd po fundamental’nym problemam teoreticeskoj i prikladnoj mehaniki: sb. dokl. - Kazan’: Izd-vo Kazan. un-ta, 2015. - S. 191-193.
  3. Anferov S.D., Skul’skij O.I., Slavnov E.V. Matematiceskoe modelirovanie processa pramogo otzima maslicnoj kul’tury // Vest. Perm. nac. issled. politehn. un-ta. Mehanika. - 2014. - No 1. - S. 31-56.
  4. Anferov S.D., Skul’skij O.I., Slavnov E.V. Model’ ekstruzionnogo otzima masla iz seman rapsa // Vycisl. meh. splos. sred. - 2015. - T. 8. - No 2. - S. 144-152.
  5. Beloborodov V.V. Osnovnye processy proizvodstva rastitel’nyh masel. - M.: Pisevaa promyslennost’, 1966. - 240 s.
  6. Berlin A.A., Rotenburg L., Baserst R. Osobennosti deformacii neuporadocennyh polimernyh i nepolimernyh tel // Vysokomolekularnye soedinenia. - 1992. - T. 34. - No 7. - S. 6-32.
  7. Vol’hin V.V., Sklaev U.V., Zernina I.A., Kazakov D.A. Biodizel’ vtorogo pokolenia: nekotorye osobennosti fiziko-himiceskih processov pri ego proizvodstve // Vest. Perm. nauc. centra. - 2010. - No 3. - S. 41-49.
  8. Petrov I.A. Modelirovanie processa snek-pressovogo otzima s ucetom osevoj fil’tracii zidkoj komponenty pererabatyvaemogo materiala // Perspektivy nauki. - 2015. - No 8(71). - S. 108-113.
  9. Petrov I.A., Slavnov E.V. Modelirovanie snek-pressovogo otzima kak sovokupnosti processov tecenia vazkoj neszimaemoj smesi i fil’tracii zidkosti skvoz’ poristuu sredu // Vycisl. meh. splos. sred. - 2013. - T. 6. - No 3. - S. 277-285.
  10. Slavnov E.V. Izmenenie pronicaemosti maslicnyh kul’tur v processe otzima masla na primere ekstrudata rapsa // Dokl. Ros. akad. sel’skohozajstvennyh nauk. - 2014. - No 3. - S. 58-60.
  11. Slavnov E.V. Sposob opredelenia zavisimosti pisevoj cennosti bioprodukta ot parametrov fiziko-mehaniceskogo vozdejstvia na nego i ustrojstvo dla etogo // Patent RF No 2385665. Opubl. 10.01.2011. - Bul. No 1.
  12. Slavnov E.V., Petrov I.A. Izmenenie vazkosti ekstrudata rapsa v processe otzima masla // Agrarnyj vestnik Urala. - 2011. - No 6. - S. 42-44.
  13. Slavnov E.V., Petrov I.A. Metod opredelenia izmenenia fil’tracionnyh svojstv maslicnyh kul’tur v processe otzima masla na primere ekstrudata rapsa // IFZ. - 2014. - T. 87. - No 4. - S. 860-864.
  14. Slavnov E.V., Petrov I.A. Vlianie skorosti ob"emnoj deformacii na intensivnost’ otzima maslicnyh kul’tur na primere ekstrudata rapsa // Inzenerno-fiziceskij zurnal. - 2015. - T. 88. - No 4. - S. 827-832.
  15. Slavnov E.V., Petrov I.A. Sposob opredelenia zavisimosti koefficienta pronicaemosti plasticeski deformiruemogo poristogo materiala kak funkcii ot massovogo soderzania i davlenia zidkosti // Patent RF No2524046. Opubl. 27.07.2014. - Bul. No 21.
  16. Slavnov E.V., Petrov I.A., Anferov S.D. Izmenenie vazkosti ekstrudata rapsa v processe otzima masla (vlianie davlenia) // Agrarnyj vestnik Urala. - 2011. - No 10. - S. 16-19.
  17. Fedorenko V.F., Buklagin D.S., Misurov N.P., Tihomirov V.S. Razvitie bioenergetiki, ekologiceskaa i prodovol’stvennaa bezopasnost’. - M.: FGNU <>, 2009. - 114 s.
  18. Slavnov E.V., Petrov I.A. Influence of Volume Deformation Rate on the Intensity of Oil-Bearing Crop Pressing-out in Relation to Rape Extrudate // Journal of Engineering Physics and Thermophysics. - 2015. - Vol. 88. - No 4. - R. 854-858. DOI 10.1007/s10891-015-1260-0.

Downloads

Published

2017-09-05

Issue

No. 2 (2017)

Section

Research: theory and experiment

How to Cite

Slavnov, E. ., Skul’skiy, O. ., Petrov, I. ., Anferov, S. ., Sudakov, A. ., & Shakirov, N. . (2017). STUDY OF THEORETICAL AND EXPERIMENTAL ASPECTS OF FLUID MOTION THROUGH PLASTICALLY DEFORMABLE POROUS MEDIA AS AN APPLICATION TO OILSEED EXTRACTION PROCESS BY THE SCREW PRESS. Perm Federal Research Centre Journal, 2, 77-83. https://journal.permsc.ru/index.php/pscj/article/view/PSCJ2017n2p11