Numerical method for determining the load capacity of flat rotating reinforced discs
DOI:
https://doi.org/10.7242/1999-6691/2024.17.3.25Keywords:
flat disks, steady-state rotation, reinforcement, rigid-plastic model, upper limit of load-bearing capacity, piecewise linear yield curves, resistance difference, plastic anisotropy, numerical solution, linear programmingAbstract
An extremal problem of determining the upper (kinematic) limit of the load-bearing capacity of a flat disk reinforced with continuous fibers and rotating in a quasi-steady state is formulated. At the inner edge, the disk blade is rigidly attached to the shaft (or hub), and reinforced vanes can be attached to its outer edge. The materials of the composition phases are assumed to be rigid-plastic, having different yield limits in tension and compression; the binder matrix material may be cylindrically orthotropic. Under conditions of a generalized plane stress state, the yield curves of the components of the composition in the principal stresses are piecewise linear. Reinforcement structures have radial and axial symmetry. The plastic deformation of the composition is calculated using the relations of the structural model of the mechanics of composites, which takes into account the plane stress state in all phase materials. The problem was discretized and a numerical algorithm for solving it was developed, based on the use of linear programming methods. Various variants of discretization of the problem under consideration have been studied. The convergence of the numerical solution and its good agreement with the previously obtained analytical solution are demonstrated. Numerical examples of calculating the maximum angular velocity of rotation of disks for different reinforcement structures of their fabric are analyzed. Cases of laying fibers along straight trajectories (geodesic lines), along logarithmic spirals, as well as along radial and circumferential directions are considered. In this case, the isotropic materials of the components of the composition obey the associated flow law corresponding to the yield criterion Hu. The influence of reinforcement parameters (directions and densities) on the bearing capacity of rotating disks has been studied. The comparison was carried out for composite disks of the same mass and with the same relative volume of reinforcement.
Downloads
References
Birger I.A., Dem’yanushko I.V. Raschet na prochnost’ vrashchayushchikhsya diskov. Moscow: Mashinostroyeniye, 1978. 247 p.
MaG., Hao H., Miyamoto Y. Limit angular velocity of rotating disc with unified yield criterion. International Journal of Mechanical Sciences. 2001. Vol. 43. P. 1137–1153. DOI: 10.1016/S0020-7403(00)00065-5
Leu S.-Y., Hsu H.-C. Exact solutions for plastic responses of orthotropic strain-hardening rotating hollow cylinders. International Journal of Mechanical Sciences. 2010. Vol. 52. P. 1579–1587. DOI: 10.1016/j.ijmecsci.2010.07.006
Faghih S., Jahed H., Behravesh S.B. Variable Material Properties Approach: A Review on Twenty Years of Progress. Journal of Pressure Vessel Technology. 2018. P. 1–63. DOI: 10.1115/1.4039068
Tahani M., Nosier A., Zebarjad S.M. Deformation and stress analysis of circumferentially fiber-reinforced composite disks. International Journal of Solids and Structures. 2005. Vol. 42. P. 2741–2754. DOI: 10.1016/j.ijsolstr.2004.09.041
Koo K.-N. Mechanical vibration and critical speeds of rotating composite laminate disks. Microsystem Technologies. 2008. Vol. 14. P. 799–807. DOI: 10.1007/s00542-007-0555-2
Zheng Y., Bahaloo H., Mousanezhad D., Vaziri A., Nayeb-Hashemi H. Displacement and Stress Fields in a Functionally Graded Fiber-Reinforced Rotating Disk With Nonuniform Thickness and Variable Angular Velocity. Journal of Engineering Materials and Technology. 2017. Vol. 139. 031010. DOI: 10.1115/1.4036242
Farukoğlu O.C., Korkut İ. On the elastic limit stresses and failure of rotating variable thickness fiber reinforced composite disk. ZAMM- Journal of Applied Mathematics and Mechanics / Zeitschrift fur Angewandte Mathematik und Mechanik. 2021. P. 1–18. DOI: 10.1002/zamm.202000356
Yankovskii A.P. Building a complete solution to the problem of determining the bearing capacity of a flat reinforced rotating disk. Computational Continuum Mechanics. 2023. Vol. 16, no. 3. P. 289–309. DOI: 10.7242/1999-6691/2023.16.3.25
Composites: State of the Art / ed. by L. Weeton, E. Scala. Metallurgical Society of AIME, 1974. 365 p.
Handbook of composites / ed. by G. Lubin. Van Nostrand Reinhold Company Inc, 1982. 786 p.
Kompozitsionnyye materialy. Spravochnik / ed. by D. Karpinos. Kyiv: Naukova dumka, 1985. 592 p.
Lenard J., Haddow J.B. Plastic collapse speeds for rotating cylinders. International Journal of Mechanical Sciences. 1972.Vol. 14. P. 285–292. DOI: 10.1016/0020-7403(72)90084-7
Yerkhov M.I. Teoriya ideal’no plasticheskikh tel i konstruktsiy. Moscow: Nauka, 1978. 352 p.
Chakrabarty J. Applied plasticity. 2nd. New York: Springer, 2010. 755 p. DOI: 10.1007/978-0-387-77674-3
Berezin I.S., Zhidkov N.P. Metody vychisleniy. Vol. 2. Moscow: Fizmatgiz, 1959. 620 p.
Zukhovitskiy S.I., Avdeyeva L.I. Lineynoye i vypukloye programmirovaniye. Moscow: Nauka, 1964. 348 p.
Romanova T.P., Yankovskii A.P. Investigation of load-bearing capacity of rigid-plastic reinforced ellipsoidal shells of rotation. Mechanics of Advanced Materials and Structures. 2023. Vol. 31, no. 18. P. 4387–4398. DOI: 10.1080/15376494.2023.2195416
Ponomarev S.D., Biderman V.L., Likharev K.K., Makushin V.M., Malinin N.N., Feodos’yev V.I. Raschety na prochnost’ v mashinostroyenii. Vol. III. Moscow: MAShGIZ, 1959. 1120 p.
Banichuk N.V., Kobelev V.V., Rikards R.B. Optimizatsiya elementov konstruktsiy iz kompozitsionnykh materialov. Moscow: Mashinostroyeniye, 1988. 224 p.
Samarskii A.A. The Theory of Difference Schemes. CRC Press, 2001. 786 p. DOI: 10.1201/9780203908518
Berezin I.S., Zhidkov N.P. Metody vychisleniy. Vol. 1. Moscow: Fizmatgiz, 1966. 632 p.
Romanova T.P., Yankovskii A.P. Load-bearing capacity of rigid-plastic reinforced shallow shells and plates. Mechanics of Advanced Materials and Structures. 2022. Vol. 29, no. 26. P. 5651–5665. DOI: 10.1080/15376494.2021.1961952
Romanova T.P., Yankovskii A.P. Piecewise-Linear Yield Loci of Angle-Ply Reinforced Medium of Different-Resisting Rigid-Plastic Materials at 2D Stress State. Mechanics of Solids. 2020. Vol. 55, no. 8. P. 1235–1252. DOI: 10.3103/S0025654420080221
Anantha Ramu S., Iyengar K.J. Plastic response of orthotropic spherical shells under blast loading. Nuclear Engineering and Design. 1979. Vol. 55, no. 3. P. 363–373. DOI: 10.1016/0029-5493(79)90115-8
Hu L.W. Modified Tresca’s yield condition and associated flow rules for anisotropic materials and applications. Journal of the Franklin Institute. 1958. Vol. 265, no. 3. P. 187–204. DOI: 10.1016/0016-0032(58)90551-9
Il’yushin A.A. Trudy (1946–1966). Vol. 2. Moscow: Fizmatlit, 2004. 480 p.
Malinin N.N. Prikladnaya teoriya plastichnosti i polzuchesti. Moscow: Mashinostroyeniye, 1975. 400 p.
Do Carmo M.P. Differential geometry of curves and surfaces. Prentice-Hall Inc, 1976. 503 p.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Computational Continuum Mechanics
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.